ซีรีส์:
VF, Mini Mill, Toolroom Mill, Super Mini Mill
รหัสคู่มือ: 96-8000 rev U
ข้อมูลเพิ่มเติม:
Mill Operator’s Manual หน้า: 114-115
| รหัส | กลุ่ม | รหัส G เริ่มต้น | ฟังก์ชัน |
|---|---|---|---|
| G00 | 01 | Rapid Motion Positioning | |
| G01 | 01 | Linear Interpolation Motion | |
| G02 | 01 | CW Circular Interpolation Motion | |
| G03 | 01 | CCW Circular Interpolation Motion | |
| G04 | 00 | Dwell | |
| G09 | 00 | Exact Stop | |
| G10 | 00 | Set Offsets | |
| G100 | 00 | Cancel Mirror Image | |
| G101 | 00 | Enable Mirror Image | |
| G102 | 00 | Programmable Output to RS-232 | |
| G103 | 00 | Limit Block Buffering | |
| G107 | 00 | Cylindrical Mapping | |
| G110 | 12 | Coordinate System #7 | |
| G111 | 12 | Coordinate System #8 | |
| G112 | 12 | Coordinate System #9 | |
| G113 | 12 | Coordinate System #10 | |
| G114 | 12 | Coordinate System #11 | |
| G115 | 12 | Coordinate System #12 | |
| G116 | 12 | Coordinate System #13 | |
| G117 | 12 | Coordinate System #14 | |
| G118 | 12 | Coordinate System #15 | |
| G119 | 12 | Coordinate System #16 | |
| G12 | 00 | Circular Pocket Milling CW | |
| G120 | 12 | Coordinate System #17 | |
| G121 | 12 | Coordinate System #18 | |
| G122 | 12 | Coordinate System #19 | |
| G123 | 12 | Coordinate System #20 | |
| G124 | 12 | Coordinate System #21 | |
| G125 | 12 | Coordinate System #22 | |
| G126 | 12 | Coordinate System #23 | |
| G127 | 12 | Coordinate System #24 | |
| G128 | 12 | Coordinate System #25 | |
| G129 | 12 | Coordinate System #26 | |
| G13 | 00 | Circular Pocket Milling CCW | |
| G136 | 00 | Automatic Work Offset Center Measurement | |
| G141 | 07 | 3D+ Cutter Compensation | |
| G143 | 08 | 5-Axis Tool Length Compensation + | |
| G150 | 00 | General Purpose Pocket Milling | |
| G153 | 09 | 5-Axis High Speed Peck Drilling Canned Cycle | |
| G154 | 12 | Select Work Coordinates P1-P99 | |
| G155 | 09 | 5-Axis Reverse Tap Canned Cycle | |
| G161 | 09 | 5-Axis Drill Canned Cycle | |
| G162 | 09 | 5-Axis Spot Drill Canned Cycle | |
| G163 | 09 | 5-Axis Normal Peck Drilling Canned Cycle | |
| G164 | 09 | 5-Axis Tapping Canned Cycle | |
| G165 | 09 | 5-Axis Boring Canned Cycle | |
| G166 | 09 | 5-Axis Bore and Stop Canned Cycle | |
| G169 | 09 | 5-Axis Bore and Dwell Canned Cycle | |
| G174 | 00 | CCW Non-Vertical Rigid Tap | |
| G184 | 00 | CW Non-Vertical Rigid Tap | |
| G187 | 00 | Setting the Smoothness Level | |
| G188 | 00 | Get Program From PST | |
| G20 | 06 | Select Inches | |
| G21 | 06 | Select Metric | |
| G28 | 00 | Return to Machine Zero | |
| G29 | 00 | Return From Reference Point | |
| G31 | 00 | Feed Until Skip | |
| G35 | 00 | Automatic Tool Diameter Measurement | |
| G36 | 00 | Automatic Work Offset Measurement | |
| G37 | 00 | Automatic Tool Offset Measurement | |
| G40 | 07 | Cutter Compensation Cancel | |
| G41 | 07 | 2D Cutter Compensation Left | |
| G42 | 07 | 2D Cutter Compensation Right | |
| G43 | 08 | Tool Length Compensation + (Add) | |
| G44 | 08 | Tool Length Compensation - (Subtract) | |
| G47 | 00 | Text Engraving | |
| G49 | 08 | Cancel Tool Length Compensation (G43/G44/G143) | |
| G50 | 11 | Cancel Scaling | |
| G51 | 11 | Scaling | |
| G52 | 00/12 | Set Work Coordinate System | |
| G53 | 00 | Non-Modal Machine Coordinate Selection | |
| G54 | 12 | Select Work Coordinate System #1 | |
| G55 | 12 | Select Work Coordinate System #2 | |
| G56 | 12 | Select Work Coordinate System #3 | |
| G57 | 12 | Select Work Coordinate System #4 | |
| G58 | 12 | Select Work Coordinate System #5 | |
| G59 | 12 | Select Work Coordinate System #6 | |
| G60 | 00 | Uni-Directional Positioning | |
| G61 | 15 | Exact Stop Mode | |
| G64 | 15 | Cancel Exact Stop Mode (G61 Cancel) | |
| G68 | 16 | Rotation | |
| G69 | 16 | Cancel Rotation | |
| G70 | 00 | Bolt Hole Circle | |
| G71 | 00 | Bolt Hole Arc | |
| G72 | 00 | Bolt Holes Along an Angle | |
| G73 | 09 | High-Speed Peck Drilling Canned Cycle | |
| G74 | 09 | Reverse Tap Canned Cycle | |
| G76 | 09 | Fine Boring Canned Cycle | |
| G77 | 09 | Back Bore Canned Cycle | |
| G80 | 09 | Canned Cycle Cancel | |
| G81 | 09 | Drill Canned Cycle | |
| G82 | 09 | Spot Drill Canned Cycle | |
| G83 | 09 | Normal Peck Drilling Canned Cycle | |
| G84 | 09 | Tapping Canned Cycle | |
| G85 | 09 | Boring Canned Cycle | |
| G86 | 09 | Bore and Stop Canned Cycle | |
| G87 | 09 | Bore In and Manual Retract Canned Cycle | |
| G88 | 09 | Bore In, Dwell, Manual Retract Canned Cycle | |
| G89 | 09 | Bore In, Dwell, Bore Out Canned Cycle | |
| G90 | 03 | Absolute Position Commands | |
| G91 | 03 | Incremental Position Commands | |
| G92 | 00 | Set Work Coordinate Systems Shift Value | |
| G93 | 05 | Inverse Time Feed Mode | |
| G94 | 05 | Feed Per Minute Mode | |
| G95 | 05 | Feed per Revolution | |
| G98 | 10 | Canned Cycle Initial Point Return | |
| G99 | 10 | Canned Cycle R Plane Return |