Siri:
CC 220/320 M
ID Panduan: Z25 NJ
Maklumat tambahan:
Programming Instructions
O = Option
S = Standard hlm.: 32-35
| Kod | Kumpulan | Kod G awal | Fungsi |
|---|---|---|---|
| G00 | 02 | Linear interpolation with rapid traverse (S) | |
| G01 | 02 | Linear interpolation with feedrate (S) | |
| G02 | 02 | Circular interpolation with feedrate, CW (S) | |
| G03 | 02 | Circular interpolation with feedrate, CCW (S) | |
| G04 | 01 | Dwell time (with F word) in seconds (S) | |
| G05 | 02 | Circular interpolation with tangential entry (S) | |
| G06 | 09 | Acceleration programming ON (O) | |
| G07 | 09 | Acceleration programming OFF (O) | |
| G08 | 11 | + | Path slope ON (S) |
| G09 | 11 | Path slope OFF (S) | |
| G10 | 02 | Linear interpolation in polar coordinates (S) | |
| G101 | Spline interpolation ON (O) | ||
| G102 | Spline interpolation OFF (O) | ||
| G104 | 01 | Dwell time (with F word) in revolutions (S) | |
| G108 | 11 | Contour-depending feedrate influencing (O) | |
| G109 | 11 | Reserved (O) | |
| G11 | 02 | Linear interpolation with feedrate in polar coordinates (S) | |
| G110 | 11 | Reserved (O) | |
| G114 | 29 | Feed forward control ON (O) | |
| G115 | 29 | + | Feed forward control OFF (O) |
| G12 | 02 | Circular interpolation with feedrate, CW in polar coordinates (S) | |
| G125 | 12 | Forbidden working area (O) | |
| G126 | 12 | Forbidden working area (O) | |
| G128 | 01 | Corner deceleration / acceleration (O) | |
| G13 | 02 | Circular interpolation with feedrate, CCW in polar coordinates (S) | |
| G14 | 13 | KV programming ON (O) | |
| G145 | 28 | + | External tool compensation ON (O) |
| G146 | 28 | External tool compensation OFF (O) | |
| G15 | 13 | KV programming OFF (O) | |
| G16 | 01 | KV measurement / compensation (O) | |
| G160 | 30 | External zero offset ON (O) | |
| G167 | 30 | + | External zero offset OFF (O) |
| G17 | 10 | + | Plane selection X Y (S) |
| G174 | 01 | Traversing to reference point via intermediate position (S) | |
| G18 | 10 | Plane selection Z X (S) | |
| G19 | 10 | Plane selection Y Z (S) | |
| G192 | 01 | Minimum limit speed (S) | |
| G20 | 10 | Selection of 2 out of 6 axes (S) | |
| G22 | 01 | Subroutine, compensation, zero-offset call (S) | |
| G23 | 01 | Conditional jump (with L word) (S) | |
| G24 | 01 | Unconditional jump (with L word) (S) | |
| G25 | 12 | Permitted working area (O) | |
| G26 | 12 | Permitted working area (O) | |
| G27 | 12 | + | Deletion of working-area limitation (O) |
| G274 | 01 | Withdrawal from reference point via intermediate position (S) | |
| G28 | 14 | Corner deceleration ON (O) | |
| G29 | 14 | Corner deceleration OFF (O) | |
| G292 | 01 | Maximum limit speed (S) | |
| G32 | 02 | Exact tapping (O) | |
| G33 | 02 | Thread cutting (O) | |
| G37 | 22 | Pole for mirror image and rotation (O) | |
| G38 | 22 | Programmable mirror image, rotation and scaling (O) | |
| G39 | 22 | Deletion of G37/G38 (O) | |
| G60 | 21 | Programmed zero offset ON (S) | |
| G61 | 23 | In position programming ON (S) | |
| G62 | 23 | + | In position programming OFF (S) |
| G63 | 05 | Set 100% feedrate (S) | |
| G64 | 25 | Feedrate override (cutter engagement point) (S) | |
| G65 | 25 | + | Feedrate override (cutter center point) (S) |
| G66 | 05 | + | Cancel G63 (S) |
| G67 | 21 | Programmed zero offset OFF (S) | |
| G68 | 26 | + | Outside corners as a radius (S) |
| G69 | 26 | Outside corners as an intersection (S) | |
| G70 | 03 | Inch programming (S) | |
| G71 | 03 | + | Metric programming (S) |
| G73 | 02 | Linear interpolation with in-position programming (S) | |
| G74 | 01 | Automatic traversing to reference point (S) | |
| G75 | 01 | Activate measuring probe input (S) | |
| G76 | 01 | Traverse to fixed machine axis position (S) | |
| G78 | 15 | Compensation and drilling cycles ON (O) | |
| G79 | 15 | Compensation and drilling cycles OFF (O) | |
| G892 | 01 | Upper limit value, laser power control (O) | |
| G90 | 04 | + | Absolute input (S) |
| G91 | 04 | Relative input (S) | |
| G92 | 01 | Set actual value (S) | |
| G93 | 07 | Time programming (S) | |
| G94 | 07 | + | Feedrate in mm/min (S) |
| G95 | 07 | Feedrate in mm/rev. (O) | |
| G98 | 27 | Rapid retract ON (S) | |
| G99 | 27 | Rapid retract OFF (S) | |
| G992 | 01 | Lower limit value, laser power control (O) | |
| G993 | 31 | Asynchronous reciprocating axis ON (O) | |
| G994 | 31 | Asynchronous reciprocating axis OFF (O) |