Sarja:
FANUC Series 0-MB
FANUC Series 00-MB
Käsikirjan ID: B-60134E/02
Lisätietoja:
Operator's Manual s.: 21-23
| Koodi | Ryhmä | Alkuperäiset G-koodit | Toiminto |
|---|---|---|---|
| G00 | 01 | + | Positioning (Rapid traverse) |
| G01 | 01 | + | Linear interpolation (Cutting feed) |
| G02 | 01 | Circular interpolation / Helical CW | |
| G03 | 01 | Circular interpolation / Helical CCW | |
| G04 | 00 | Dwell, Exact stop | |
| G09 | 00 | Exact stop | |
| G10 | 00 | Data setting | |
| G11 | 00 | Data setting mode cancel | |
| G17 | 02 | + | XY plane selection |
| G18 | 02 | ZX plane selection | |
| G19 | 02 | YZ plane selection | |
| G20 | 06 | Input in inch | |
| G21 | 06 | Input in mm | |
| G27 | 00 | Reference point return check | |
| G28 | 00 | Return to reference point | |
| G29 | 00 | Return from reference point | |
| G30 | 00 | 2nd reference point return | |
| G31 | 00 | Skip function | |
| G33 | 01 | Thread cutting | |
| G39 | 00 | Corner offset circular interpolation | |
| G40 | 07 | + | Cutter compensation cancel |
| G41 | 07 | Cutter compensation left | |
| G42 | 07 | Cutter compensation right | |
| G43 | 08 | Tool length compensation + direction | |
| G44 | 08 | Tool length compensation - direction | |
| G49 | 08 | + | Tool length compensation cancel |
| G50 | 11 | + | Scaling cancel |
| G51 | 11 | Scaling | |
| G54 | 14 | + | Work coordinate system 1 selection |
| G55 | 14 | Work coordinate system 2 selection | |
| G56 | 14 | Work coordinate system 3 selection | |
| G57 | 14 | Work coordinate system 4 selection | |
| G58 | 14 | Work coordinate system 5 selection | |
| G59 | 14 | Work coordinate system 6 selection | |
| G60 | 00 | Single direction positioning | |
| G61 | 15 | Exact stop mode | |
| G62 | 15 | Automatic corner override | |
| G63 | 15 | Tapping mode | |
| G64 | 15 | + | Cutting mode |
| G65 | 00 | Macro call, Macro command | |
| G66 | 12 | Macro modal call | |
| G67 | 12 | + | Macro modal call cancel |
| G68 | 16 | Coordinate rotation | |
| G69 | 16 | + | Coordinate rotation cancel |
| G73 | 09 | Peck drilling cycle | |
| G74 | 09 | Counter tapping cycle | |
| G76 | 09 | Fine boring | |
| G80 | 09 | + | Canned cycle cancel |
| G81 | 09 | Drilling cycle, spot boring | |
| G82 | 09 | Drilling cycle, counter boring | |
| G83 | 09 | Peck drilling cycle | |
| G84 | 09 | Tapping cycle | |
| G85 | 09 | Boring cycle | |
| G86 | 09 | Boring cycle | |
| G87 | 09 | Back boring cycle | |
| G88 | 09 | Boring cycle | |
| G89 | 09 | Boring cycle | |
| G90 | 03 | + | Absolute command |
| G91 | 03 | Incremental command | |
| G92 | 00 | Programming of absolute zero point | |
| G94 | 05 | + | Feed per minute |
| G95 | 05 | Feed per rotation | |
| G98 | 10 | + | Return to initial point in canned cycle |
| G99 | 10 | Return to R point in canned cycle |