সিরিজ:
Series 16 / 18 / 160 / 180 – Model C
for Machining Center
ম্যানুয়াল আইডি: B–62764EN/01
অতিরিক্ত তথ্য:
Operator's Manual পৃষ্ঠা: 35-37
| কোড | গ্রুপ | প্রাথমিক G কোড | ফাংশন |
|---|---|---|---|
| G00 | 00 | + | Positioning |
| G01 | 00 | + | Linear interpolation |
| G02 | 01 | Circular interpolation/Helical interpolation CW | |
| G02.2, G03.2 | 01 | Involute interpolation | |
| G02.3, G03.3 | 01 | Exponential interpolation | |
| G03 | 01 | Circular interpolation/Helical interpolation CCW | |
| G04 | 00 | Dwell, Exact stop | |
| G05 | 00 | High speed cycle machining | |
| G07.1 (G107) | 00 | Cylindrical interpolation | |
| G08 | 00 | Look–ahead control | |
| G09 | 00 | Exact stop | |
| G10 | 00 | Programmable data input | |
| G10.6 | 00 | Tool retract & recover | |
| G11 | 00 | Programmable data input mode cancel | |
| G12.1 | 25 | Polar coordinate interpolation mode | |
| G13.1 | 25 | + | Polar coordinate interpolation cancel mode |
| G15 | 17 | + | Polar coordinates command cancel |
| G16 | 17 | Polar coordinates command | |
| G160 | 20 | + | In–feed control function cancel (for grinding machine) |
| G161 | 20 | In–feed control function (for grinding machine) | |
| G17 | 02 | + | XpYp plane selection (X axis or parallel) |
| G18 | 02 | + | ZpXp plane selection (Y axis or parallel) |
| G19 | 02 | + | YpZp plane selection (Z axis or parallel) |
| G20 | 06 | Input in inch | |
| G21 | 06 | Input in mm | |
| G22 | 04 | + | Stored stroke check function on |
| G23 | 04 | Stored stroke check function off | |
| G25 | 24 | Spindle speed fluctuation detection off | |
| G26 | 24 | + | Spindle speed fluctuation detection on |
| G27 | 00 | Reference position return check | |
| G28 | 00 | Return to reference position | |
| G29 | 00 | Return from reference position | |
| G30 | 00 | 2nd, 3rd and 4th reference position return | |
| G30.1 | 00 | Floating reference point return | |
| G31 | 00 | Skip function | |
| G33 | 01 | Thread cutting | |
| G37 | 00 | Automatic tool length measurement | |
| G39 | 00 | Corner offset circular interpolation | |
| G40 | 07 | + | Cutter compensation cancel / Three dimensional compensation cancel |
| G40.1 (G150) | 19 | + | Normal direction control cancel mode |
| G41 | 07 | Cutter compensation left / Three dimensional compensation | |
| G41.1 (G151) | 19 | Normal direction control left side on | |
| G42 | 07 | Cutter compensation right | |
| G42.1 (G152) | 19 | Normal direction control right side on | |
| G43 | 08 | Tool length compensation + direction | |
| G44 | 08 | Tool length compensation – direction | |
| G45 | 00 | Tool offset increase | |
| G46 | 00 | Tool offset decrease | |
| G47 | 00 | Tool offset double increase | |
| G48 | 00 | Tool offset double decrease | |
| G49 | 08 | + | Tool length compensation cancel |
| G50 | 11 | + | Scaling cancel |
| G50.1 | 22 | + | Programmable mirror image cancel |
| G51 | 11 | Scaling | |
| G51.1 | 22 | Programmable mirror image | |
| G52 | 00 | Local coordinate system setting | |
| G53 | 00 | Machine coordinate system selection | |
| G54 | 14 | + | Workpiece coordinate system 1 selection |
| G54.1 | 14 | Additional workpiece coordinate system selection | |
| G55 | 14 | Workpiece coordinate system 2 selection | |
| G56 | 14 | Workpiece coordinate system 3 selection | |
| G57 | 14 | Workpiece coordinate system 4 selection | |
| G58 | 14 | Workpiece coordinate system 5 selection | |
| G59 | 14 | Workpiece coordinate system 6 selection | |
| G60 | 00 | Single direction positioning | |
| G61 | 15 | Exact stop mode | |
| G62 | 15 | Automatic corner override | |
| G63 | 15 | Tapping mode | |
| G64 | 15 | + | Cutting mode |
| G65 | 00 | Macro call | |
| G66 | 12 | Macro modal call | |
| G67 | 12 | + | Macro modal call cancel |
| G68 | 16 | Coordinate rotation | |
| G69 | 16 | + | Coordinate rotation cancel |
| G73 | 09 | Peck drilling cycle | |
| G74 | 09 | Counter tapping cycle | |
| G75 | 01 | Plunge grinding cycle (for grinding machine) | |
| G76 | 09 | Fine boring cycle | |
| G77 | 01 | Direct constant–dimension plunge grinding cycle (for grinding machine) | |
| G78 | 01 | Continuous–feed surface grinding cycle (for grinding machine) | |
| G79 | 01 | Intermittent–feed surface grinding cycle (for grinding machine) | |
| G80 | 09 | + | Canned cycle cancel / External operation function cancel |
| G81 | 09 | Drilling cycle, spot boring cycle or external operation function | |
| G82 | 09 | Drilling cycle or counter boring cycle | |
| G83 | 09 | Peck drilling cycle | |
| G84 | 09 | Tapping cycle | |
| G85 | 09 | Boring cycle | |
| G86 | 09 | Boring cycle | |
| G87 | 09 | Back boring cycle | |
| G88 | 09 | Boring cycle | |
| G89 | 09 | Boring cycle | |
| G90 | 03 | + | Absolute command |
| G91 | 03 | + | Increment command |
| G92 | 00 | Setting for work coordinate system or clamp at maximum spindle speed | |
| G92.1 | 00 | Workpiece coordinate system preset | |
| G94 | 05 | + | Feed per minute |
| G95 | 05 | Feed per rotation | |
| G96 | 13 | Constant surface speed control | |
| G97 | 13 | + | Constant surface speed control cancel |
| G98 | 10 | + | Return to initial point in canned cycle |
| G99 | 10 | Return to R point in canned cycle |