Seriya:
Series 20-FA
Təlimat ID-si: B-62174E/03
Əlavə məlumat:
Operator's Manual səh.: 31-33
| Kod | Qrup | İlkin G kodları | Funksiya |
|---|---|---|---|
| G00 | 01 | + | Positioning |
| G01 | 01 | + | Linear interpolation |
| G02 | 01 | Circular interpolation / Helical interpolation CW | |
| G03 | 01 | Circular interpolation / Helical interpolation CCW | |
| G04 | 00 | Dwell, Exact stop | |
| G09 | 00 | Exact stop | |
| G10 | 00 | Data setting | |
| G11 | 00 | Data setting mode cancel | |
| G17 | 02 | + | XY plane selection |
| G18 | 02 | + | ZX plane selection |
| G19 | 02 | + | YZ plane selection |
| G20 | 06 | Input in inch | |
| G21 | 06 | Input in mm | |
| G22 | 04 | + | Stored stroke check function on |
| G23 | 04 | Stored stroke check function off | |
| G27 | 00 | Reference position return check | |
| G28 | 00 | Return to reference position | |
| G29 | 00 | Return from reference position | |
| G30 | 00 | 2nd reference position return | |
| G31 | 00 | Skip function | |
| G40 | 07 | + | Cutter compensation cancel |
| G41 | 07 | Cutter compensation left | |
| G42 | 07 | Cutter compensation right | |
| G43 | 08 | Tool length compensation + direction | |
| G44 | 08 | Tool length compensation – direction | |
| G49 | 08 | + | Tool length compensation cancel |
| G50 | 11 | + | Scaling cancel |
| G51 | 11 | Scaling | |
| G52 | 00 | Local coordinate system setting | |
| G53 | 00 | Machine coordinate system selection | |
| G54 | 14 | + | Workpiece coordinate system 1 selection |
| G55 | 14 | Workpiece coordinate system 2 selection | |
| G56 | 14 | Workpiece coordinate system 3 selection | |
| G57 | 14 | Workpiece coordinate system 4 selection | |
| G58 | 14 | Workpiece coordinate system 5 selection | |
| G59 | 14 | Workpiece coordinate system 6 selection | |
| G60 | 00 | Single direction positioning | |
| G61 | 15 | Exact stop mode | |
| G63 | 15 | Tapping mode | |
| G64 | 15 | + | Cutting mode |
| G65 | 00 | Macro call | |
| G66 | 12 | Macro modal call | |
| G67 | 12 | + | Macro modal call cancel |
| G68 | 16 | Coordinate rotation | |
| G69 | 16 | + | Coordinate rotation cancel |
| G73 | 09 | Peck drilling cycle | |
| G74 | 09 | Counter tapping cycle | |
| G76 | 09 | Fine boring cycle | |
| G80 | 09 | + | Canned cycle / external operation function cancel |
| G81 | 09 | Drilling cycle or spot boring / external operation function | |
| G82 | 09 | Drilling cycle or counter boring cycle | |
| G83 | 09 | Peck drilling cycle | |
| G84 | 09 | Tapping cycle | |
| G85 | 09 | Boring cycle | |
| G86 | 09 | Boring cycle | |
| G87 | 09 | Back boring cycle | |
| G88 | 09 | Boring cycle | |
| G89 | 09 | Boring cycle | |
| G90 | 03 | + | Absolute command |
| G91 | 03 | + | Increment command |
| G92 | 00 | Setting for work coordinate system or clamp at maximum spindle speed | |
| G94 | 05 | + | Feed per minute |
| G98 | 10 | + | Return to initial point in canned cycle |
| G99 | 10 | Return to R point in canned cycle |